Meta toluene sulphonic acid and related compounds
Date: 2018-05-05T00:00:00+00:00
Keywords: Organic compounds -- Synthesis; Sulfonic acids

The Project Gutenberg eBook of Meta toluene sulphonic acid and related compounds

This ebook is for the use of anyone anywhere in the United States and most other parts of the world at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg License included with this ebook or online at www.gutenberg.org. If you are not located in the United States, you will have to check the laws of the country where you are located before using this eBook.

Title: Meta toluene sulphonic acid and related compounds

Author: C. F. H. Allen

Release date: May 5, 2018 [eBook #57089]

Language: English

Credits: Produced by Wayne Hammond and The Online Distributed
Proofreading Team at http://www.pgdp.net (This file was
produced from images generously made available by The
Internet Archive)

*** START OF THE PROJECT GUTENBERG EBOOK META TOLUENE SULPHONIC ACID AND RELATED COMPOUNDS ***

BOSTON UNIVERSITY
GRADUATE SCHOOL
THESIS
META TOLUENE SULPHONIC ACID and RELATED COMPOUNDS

Submitted by
Charles Francis Hitchcock Allen
(A.B., Boston University, 1919)

In partial fulfilment of requirements for
the degree of Master of Arts
1920

Table of Contents.

| Page
META TOLUENE SULPHONIC ACID and RELATED COMPOUNDS | 1
THEORETICAL DISCUSSION | 8
SULPHONATION OF ORTHO TOLUIDINE | 12
SULPHONATION OF PARA TOLUIDINE | 16
DIAZOTIZATION OF ORTHO TOLUIDINE SULPHONIC ACID. | 21
PHYSICAL PROPERTIES OF THE DIAZO COMPOUND | 23
DECOMPOSITION OF THE DIAZO COMPOUND | 24
A STUDY OF THE SOLUTION OBTAINED BY THE DECOMPOSITION OF THE DIAZO COMPOUND | 26
CONCLUSION | 29
BIBLIOGRAPHY | 30

META TOLUENE SULPHONIC ACID and RELATED COMPOUNDS

Theoretically toluene should yield three isomeric mono sulphonic acids, in which the entering sulphonic acid group occupies the positions ortho, meta, or para to the methyl group.

The action of sulphuric acid on toluene was first investigated by Jaworsky, (Ztschr. Chem. 1,272), who described one toluene sulphonic acid as the resulting compound. In 1869 Engelhardt and Latschinoff (Ibid. 617), heated toluene with sulphuric acid and made and studied the potassium salt of the resulting acid. They obtained two forms, and identified them by fusion with caustic potash which converted them into the ortho and para cresols, showing that sulphonation had taken place in the positions ortho and para to the methyl group.

Barth (Ann. chem. (Liebig) 152,91), working similarly but fusing under different conditions which also caused oxidation of the methyl group to a carboxyl group obtained para hydroxy benzoic acid and salicylic acid (ortho hydroxy benzoic acid.) This also proved that the sulphonic acid group had entered in the ortho and para positions.

Anna Wolkow (Ztschr. Chem (1870) 321), confirmed this work but ascribed the meta position to the sulphonic acid that passed into salicylic acid. She also made two acid chlorides and amides and recorded their melting points.

Fittig and Ramsay (Ann. chem. (Liebig) 168,242) studied this result of Anna Wolkow, and to determine and settle the constitutions of the sulphonic acids, carefully prepared and purified their sulphonic acids; they proved definitely that no meta acid was formed, and that the products were only the ortho and para toluene sulphonic acids.

Hubner and Post (Ann. chem. (Liebig) 169,47) worked on pure para brom toluene, and obtained two para brom toluene mono-sulphonic acids, one of which they proved to be the ortho acid by removal of the bromine by metallic sodium, and oxidation to salicylic acid. By exclusion they decided that the other acid must be one containing the sulphonic acid group in meta position to the methyl group.

F.C.G. Müller (same as Hubner and Post) made the barium salt of ortho brom toluene sulphonic acid, and then removed the bromine by treatment with sodium amalgam. The excess of alkali was removed by sulphuric acid, the sodium sulphate removed by evaporation and crystallization, and the residue dried. On treatment with phosphorus pentachloride an oily toluene sulphonchloride was obtained; this was decomposed by heating with water, the hydrochloric acid removed by repeated evaporations, and the syrup thus obtained evaporated to a crystalline condition. Several salts were made and studied. His amide melted at 90-91. Because this acid differed in properties from the two previously mentioned, Müller considered it to be the meta toluene sulphonic acid.

About this time F. Gervor (Ann. chem. (Liebig) 169,383), made ortho diazo toluene sulphonic acid by subjecting ortho toluidine sulphonic acid to nitrous fumes. This was decomposed with alcohol under pressure, and a sodium salt of the acid obtained; this was converted into the chloride and an amide which melted at 148, differing in this and other properties from the amides of the ortho and para toluene sulphonic acids previously known.

In 1874 Pechmann (Ibid., 173,195) obtained a quantity of para toluidine meta sulphonic acid by heating para toluidine with sulphuric acid, and crystallizing out the para toluidine ortho sulphonic acid and disulphonic acids, leaving the meta acid in solution because of its greater solubility. The diazo compound was made by treatment of the acid in alcoholic suspension with nitrous fumes, and decomposed with alcohol under pressure. Various salts of the resulting sulphonic acid were made and studied, also the chloride and amide which melted "somewhere below 100".

In 1875 Pagel (Ann. chem. (Liebig) 176,297) working on ortho toluidine sulphonic acid, made a toluene sulphonic acid which resembled Muller’s. His amide melted at 104.

In 1877 Beckurts (Ber.d.che. Ges. 10, 943), seeking for a good method of obtaining pure ortho toluene sulphonic acid, heated toluene and sulphuric acid in the ordinary way, and made the potassium salts of the resulting acids. By treatment with phosphorus pentachloride he obtained the acid chlorides which he separated by cooling to -15, and filtering off the solid para compound. The remaining liquid was transformed into an amide and purified by fractional crystallization. Two compounds were obtained with sharp melting points of 153 and 104. From this work he concluded that the sulphonation of toluene yielded all the three possible acids.

Fahlberg (Am. Chem. J. 1, 170), doubted Beckurts’ statement, because although his acid showed different properties he neglected to prove its constitution by converting it into the hydroxy benzoic acid. He therefore repeated Beckurts’ work, and identified the amide melting at 154 as coming from ortho toluene sulphonic acid, by conversion into salicylic acid. The other amide with a sharp, constant melting point of 108 was oxidized, and the products separated and identified as para sulphamine benzoic acid, anhydro ortho sulphamine benzoic acid, and acid potassium ortho sulphobenzoate. These were the products one would expect from an oxidation of a mixture of the ortho and para toluene sulphonamides. Further proof that his acid was a mixture was obtained by mixing amounts of pure ortho and para toluene sulphonic acids, and by repeated crystallizations a form was obtained which melted at 108.

F.H.S. Muller (Ber. d. chem. Ges. 13, 1348), mentioned the formation of meta toluene sulphonic acid by the action of sulphurous acid upon the corresponding diazo compound, but gave no details except the melting points of his amide, anilide, and toluide.

Claesson and Wallin in 1879 (Ibid. p. 1848), claimed that they had obtained meta toluene sulphonic acid by the action of chlorsulphonic acid upon toluene. They used very large quantities of materials. They obtained three acids, and identified them as the ortho and para, and called the third the meta acid, despite the fact that they had knowledge of Fahlberg’s work.

The next step was undertaken by R. Otto (Ibid, 13, 1292), at the request of Beckurts. He examined some of the latter’s supposed meta toluene sulphonamide, and found it to be a mixture of the amides of the ortho and para acids.

Nevile and Winther (Ibid. 13, 1940), while investigating the formation of amino sulphonic acids, obtained a toluene sulphonic acid by heating ortho diazo toluene sulphonic acid with alcohol under pressure, and also by reducing brom toluene sulphonic acid with sodium amalgam. It was converted into the chloride and amide,—the latter melting at 106.5-107.5.

In 1886, Valin (Ibid. 2952), convinced by the work of Otto that Fahlberg’s views were correct, and that he and Klason had not obtained meta toluene sulphonic acid, again attacked the problem; an acid was made and salts described.

In 1891, Metcalf (Am. Che. J. 15,301) (Dissertation, 1892), proved that decomposition of para diazo toluene meta sulphonic acid with ethyl alcohol under pressure resulted in the formation of para ethoxy meta toluene sulphonic acid in far greater quantity. Consequently the toluene meta sulphonic acid could not have been obtained by either Pechmann or Valin.

Griffin, (Dissertation, 1895), prepared what he thought was a solution of the meta toluene sulphonic acid from the amide, and made and studied several salts as well as the anilide and toluide. However he did not investigate his solution to find out what it contained, but went ahead on the assumption that he had a solution of this acid. It is on the basis of his lack of investigation that I am working.

The derivatives of para toluene sulphonic acid have been made and studied by Newell, (Dissertation, 1895), and are being investigated further. He prepared para tolyl phenyl sulphone by the Friedal-Crafts reaction, para phenyl sulphone benzoic acid by oxidation of the sulphone with chromic acid, its salts, chloride, amide, and anilide, and para benzoyl diphenyl sulphone from the acid by the Friedal-Crafts reaction, and studied their reactions and properties.

The analogous derivatives of ortho toluene sulphonic acid were made and studied by Canter, (Dissertation, 1900). He prepared ortho tolyl phenyl sulphone by the Friedal-Crafts reaction, ortho phenyl sulphone benzoic acid by oxidation of the sulphone by potassium permanganate, its chloride, amide, and anilide, and ortho benzoyl diphenyl sulphone from the acid by the Friedal-Crafts reaction.

The analogous derivatives of the meta toluene sulphonic acid with one or two exceptions have not been made or studied, nor has the acid itself been prepared in a form which could be recognized. The following derivatives of meta toluene sulphonic acid have been made and studied; the amide by Müller, Pechmann, Pagel, Beckurts, F.H.S. Muller, Nevile and Winther, Chase Palmer, Klason, Valin, Noyes and Walker, Metcalf, and Griffin; meta sulphamine benzoic acid by Limpricht and Uslar, and Griffin; meta toluene sulphon anilide and toluide by Muller and Wiesinger, (Ber. d. chem. Ges, 12,1348), and by Griffin; the latter also made and studied several metallic salts.

The literature on the ortho and para toluene sulphonic acids and their derivatives is voluminous, and covers a great many derivatives which have been thoroughly studied and whose structure has been determined. The literature on meta toluene sulphonic acid is very meagre, comparatively, and all that could be found is mentioned in this paper. This would seem to indicate that investigators have avoided this series, and apparently the reason is due to the difficulties encountered in isolating the free acid.

THEORETICAL DISCUSSION

The object of this paper is to prepare a solution of meta toluene sulphonic acid, as probably obtained by Griffin, by the most promising of the investigated methods and to find an acceptable one for isolating the acid in the solid state. After a solution is obtained similar to that found by Griffin, (loc. cit.), the intention is to remove as much water as possible by distillation under diminished pressure and then to precipitate the acid by the method of Kastle, (Amer. Chem. J., Vol. 44, page 483), namely saturate the remaining solution with gaseous hydrochloric acid. It is hoped that in this way the solid acid may be obtained which can then be studied.

As has been proved by previous experimenters and discussed above, no direct method of sulphonating toluene will give any of the meta sulphonic acid. Therefore to get a compound containing a methyl group with a sulphonic acid group in the position meta to it some compound with these already in that position and containing some other group which can be replaced by hydrogen might be used, i.e. a disubstituted toluene. The two groups which can be readily replaced by hydrogen are the amino group and bromine, the former by the diazo reaction and the latter by treatment with metallic sodium; the easier of the two to prepare and replace is the amino group and this is the one made use of in this synthesis. This replacement has been widely studied (Amer. Chem. J., by Palmer 8, 243; Orndorff 9, 387; Graham 11, 319; Dashiell 15, 124; Metcalf 15, 301; Parks 15, 320; Shober 15, 379; Beeson 16, 244; and Dissertations by Weida, Cameron, and Chamberlain, all 1894.), and the various conditions affecting it determined. The foregoing investigators decomposed their diazo compounds with alcohols sometimes using certain substances to cause the alkoxy or hydrogen reactions to take place. Later investigators (Buchka, Berichte 23, 1628, St. Von Niemantowski, Ibid., 34, 3325 (1901), Ullman and Bieleck, Ibid., 34, 2174, and Bigelow, J. Amer. Chem. Soc., Vol. 41, 1566), have shown that this decomposition is greatly increased by the presence of copper powder. As the first method has been more extensively studied it was adopted in this case.

The action of methyl, ethyl, and n-propyl alcohols on diazo compounds has been well studied by the above authors, and it has been shown that the first two at ordinary pressures give the alkoxy reaction either in whole or in part; n-propyl alcohol gives the hydrogen reaction only. Also the first two give the hydrogen reaction in the presence of zinc dust or sodium carbonate, but in these cases form salts of the acid. On account of its rarity n-propyl alcohol was not used, but n-butyl alcohol which is available in large quantities and in a pure condition was employed. Recent advances in fermentation as applied to organic chemistry have made this substance easily obtainable as a byproduct in the production of acetone which was needed in large amounts during the late war. Its use was found to be successful; it boils at 117 and so can be easily distilled off after decomposition has been effected without a great increase in temperature above the boiling point of water, which increase Griffin (loc. cit.) showed to cause carbonization. For this reason i-amyl alcohol although available was not considered,—also higher alcohols because of this fact and because of their rarity.

Of the four amino toluene sulphonic acids theoretically possible in which the sulphonic acid group is in the meta position in reference to the methyl group only two are commonly known, No. 1, and No. 2.

Methods of preparing No. 1 and No. 2 were found but without details, so a method had to be worked out to obtain them easily and in good yield. After a little experimenting No. 1, or ortho toluidine sulphonic acid was readily obtained in good yield and in a fairly pure condition. No. 2, or para toluidine meta sulphonic acid was obtained in only a ten per cent yield and by means of a much more difficult method of procedure. The preparation of this acid was undertaken first and consumed a long time; Griffin did his work starting with this acid and I hoped to get as far as he did earlier. It was then available in the market as was the ortho toluidine sulphonic acid, but now neither are available.

The methods employed by earlier investigators when they wished to isolate their diazo compounds was to suspend the substance to be diazotized in alcohol, and then pass in nitrous fumes generated by dropping concentrated nitric acid onto arsenious oxide. The diazo compound from ortho toluidine sulphonic acid is so nearly insoluble in water that it was found possible to diazotize it in water suspension, and generate the nitrous fumes in the solution itself by adding a solution of sodium nitrite to the water suspension containing hydrochloric acid. After a short time the diazo compound separates out and can be filtered off, washed and dried. It is a very stable substance as compared with other diazo compounds. This method was worked out, there being no mention of it in the literature.

SULPHONATION OF ORTHO TOLUIDINE

Of the possible sulphonic acids of ortho toluidine the commercial product of former days was the one in which the sulphonic acid group was in the para position to the amino group, and meta to the methyl group; thus this acid could find use in preparing the toluene meta sulphonic acid if a method of replacing the amino group by hydrogen could be found. This acid is not now on the market in America because of its limited use in dyestuffs. It is mentioned in Schultz and Julius, (“Farbestoff Tabellen”, 1894 Edition, Trans. by F. C. Green), Cain, (“The Manufacture of Intermediate Products for Dyes”) and Nevile and Winther, (Ber. d. chem. Ges. 13, 1940.), which latter give a method of preparation which was used industrially,—the baking of ortho toluidine sulphate. Their description is rather indefinite but after a few preliminary trials a suitable method was found. I will describe all the experiments attempted, and include the one finally adopted. The ortho toluidine used was (“Practical.”) obtained from Eastman Kodak Co.

Experiment 1.

Ortho toluidine was suspended in water and conc. sulphuric acid added with vigorous stirring until all the amine had dissolved. The solution was heated to boiling until the sulphate had dissolved, and then cooled and the crystals thus obtained filtered off and dried. This was then powdered and ground with some powdered oxalic acid. These mixtures with and without oxalic acid were then baked until a sample was completely soluble in sodium hydroxide. The mass had become a deep grayish purple. It dissolved in water to give a deep red solution. Nothing satisfactory was obtained from any of these bakes, the formation of a red dyestuff as mentioned by Nevile and Winther seeming to be formed in a great quantity and very easily. Hence this method was discarded.

Experiment 2.

In this case an excess of sulphuric acid was used. After the oxalic acid had all been decomposed or driven off the mass turned black and became very pitchy. Nothing could be done with it so it was thrown away.

Experiment 3.

In this case an excess of ortho toluidine was used. The red dyestuff was formed in great amount and very easily. The temperature was kept below 195 to lose none of the toluidine which boiled at 199.

Experiment 4.

This method gave the best results and is the one employed in the preparation of all the material used in the thesis. Equal weights of ortho toluidine and sulphuric acid (100gms. of each were used; 100gms. of ortho toluidine is 108cc., and 100gms. of sulphuric acid (s. g. 1.84) are 56cc.), were mixed and baked at 190-195 until a sample would dissolve in ten per cent sodium hydroxide solution to give a clear solution; this took one and a half hours. The mixture at first melts in the solution of the sulphate and sulphuric acid formed by the heat of combination; as heating is continued it gradually becomes solid and finally very hard; it has become gray in color. When it is perfectly dry a test is made to see if it dissolves in sodium hydroxide giving a clear solution. If so, sulphonation is complete. By using an oven with a glass door the reaction mixture can be watched and the completion of the baking observed. However the test for complete solubility should always be made. The addition of powdered oxalic acid to the reaction mixture did not seem to be of advantage, because no visible reaction commenced until this had been driven off or decomposed. It is usually added in producing sulphonic acids by baking the sulphates of the amines to increase the porosity of the mass and thus facilitate removal of the product. However here the only effect seemed to be to retard the reaction, as the product was the sane hard grayish mass as without the acid, and it was just as difficult to dig it out. It took an hour longer to complete the reaction with the addition of the oxalic acid.

The best results were obtained when the temperature of the oven was kept at 193, although five degrees variation did not appreciably affect the product. A lower temperature gives little or no action, while a higher one drives off the ortho toluidine and also seems to favor the formation of the red dyestuff.

As stated above, complete sulphonation is shown by the solubility of the acid in ten per cent sodium hydroxide solution. If any unchanged amine is present as sulphate the solution will become milky due to liberation of the insoluble amine. On boiling a solution of the acid a slight hydrolysis takes place so that the smell of ortho toluidine is present, yet the solution is always perfectly clear.

The product or “bake” appears as a hard grayish mass, slightly porous. It is dug out, pulverized, boiled up in a large evaporating dish, containing water and a little (10cc.) hydrochloric acid, with animal charcoal and filtered. The solution should be almost colorless. The effect of the slight amount of hydrochloric acid was accidental; the first solutions were always a deep red color due to some of the red dyestuff seeming to be present, and the longer the solution was boiled the redder it got. A little acid seems to prevent this entirely. The solution is evaporated on a water bath until a scum has formed on the surface when it is allowed to cool and crystallize. It crystallizes in small almost white needles, which appear to fill the entire liquid; this is deceptive as on filtering the bulk is considerably reduced. They fall to a powder when they are dry. If they are colored red or pink they are washed while still on the filter with water; alcohol does not remove this color.

The acid as formed has no melting point, but chars and decomposes on heating. A sample was tested for nitrogen and sulphur with very good positive results. On fusion with caustic soda and acidification of the product a positive reaction was obtained on the addition of bromine water as is customary with phenols.

It was identified as identical with the acid of Nevile and Winther (loc. cit.) by conversion thru the diazo compound into dinitro ortho cresol, melting at 85.8 as described under the description of the diazo compound.

SULPHONATION OF PARA TOLUIDINE

Metcalf, (loc. cit.), gives a method for the preparation of the sulphonic acids of para toluidine, and states that both the possible acids are formed, with the meta position (referred to the methyl group) in good yield. Schultz and Julius, (“Farbestoff Tabellen”, 1894 Edition, Trans, by F. C. Green), and Nevile and Winther, (loc. cit.), say that the sulphonation of para toluidine gives a mixture of the sulphonic acids, with the ortho (referred to the methyl group) sulphonic acid in a much greater yield. As the sulphonation of para nitro toluene gives (Dissertation, R. S. Norris, BPL. 5976.109) a ninety-five per cent yield of the ortho sulphonic acid, it would seem as though the amino compound should give a large yield of the acid (sulphonic acid group ortho to the methyl group,) and such was found to be the case.

I followed Metcalf’s directions as follows: in an apparatus fitted with an automatic stirrer and a thermometer I placed 200 grams (110cc.) of twenty per cent fuming sulphuric acid. I then slowly added with rapid stirring 100grams of powdered para toluidine which was obtained from the Newport Chemical Works. The addition took thirteen minutes. The initial temperature of the solution was 18°C. The maximum was obtained when about half the toluidine had been added and was 148°C. The final temperature was 130°C. After addition was complete I stirred for five minutes, and then slowly heated the mixture to 180°C. and kept it there for an hour. Sulphonation was then complete. I then poured it into an equal volume of cold water (220cc.) in an evaporating dish and allowed it to stand over night. The next day the dish seemed filled with grayish crystals; these were filtered off. The solution was allowed to stand for four weeks with no results. (Metcalf says that the disulphonic acid separated in three weeks from his solution.)

I dissolved the crude acid obtained as above in ten liters of water (Metcalf’s directions) and precipitated the excess of sulphuric acid with barium hydroxide, and then filtered the solution. It was a clear brownish color. I then evaporated to 100cc. A smell of para toluidine was always present in the vapor indicating a probable hydrolysis of the acid. (Nevile and Winther (loc. cit.) say that this sulphonic acid can be hydrolyzed by heating with water), A test after sulphonation and before evaporation showed a sample to be completely soluble in water, and no cloudiness was produced when a sample was dissolved in sodium hydroxide, as is the case if a solution of para toluidine sulphate is dissolved in the same reagent. When the volume had reached 100cc. a light brown crust had formed on top of the liquid and on cooling and filtering two products were obtained; a light brown powdery substance in larger amount (47.5 grams.), and a small amount of hard square brown crystals. On evaporating the filtrate nearly to dryness more material separated which did not look like either of the above substances; it weighed twenty grams. This has not been investigated as yet.

As the brownish powdery substance was mixed with the flat crystals produced above, a method had to be found to separate them and purify each. I screened them as much as possible with good results. I removed the last of the fine powder by dissolving it off with hot water. Metcalf said that they could be separated by their difference in specific gravity in fifty per cent alcohol but this method was unsuccessful. I boiled up the aqueous solution of the powdery substance with animal charcoal, filtered and evaporated to crystallization. Square, flat, white crystals were obtained identical in all but color with those mentioned above. They are soluble with difficulty in cold water, readily in hot, and insoluble in alcohol. In these properties and in appearance they compare to the ortho sulphonic acid of para toluidine as made and described by Parks, (Dissertation, 1892). Metcalf and Nevile and Winther say that the meta sulphonic acid of para toluidine forms needles, but I obtained nothing that could in any way be called needles. This sulphonic acid had no melting point, but charred and decomposed. A test for elements showed nitrogen and sulphur to be present. The aqueous solution had a strong acid reaction to litmus.

In order to see if this might be the desired acid I tried to prepare an acid chloride with phosphorus pentachloride in the usual way, and then intended to convert it into the amide and get a melting point for identification. I used equal weights of the acid and phosphorus pentachloride. I ground them together at ordinary temperature in a mortar: no result. I heated it on a water bath: no result. I heated it on a gauze over a flame: no result except decomposition and carbonization. However I poured water into the mixture and decomposed the excess of phosphorus pentachloride, and filtered. A gummy brownish mass remained which was insoluble in all reagents tried, (methyl and ethyl alcohol, benzine, petroleum ether, (40-60), water, carbon tetrachloride, dilute hydrochloric acid, acetone, and acetic acid.) Ethyl ether extracted a very small amount, just enough to color it yellow, and leave a yellow color on porcelain on evaporation, but not enough to make a study of the properties. On shaking up with concentrated ammonia the mass became very finely divided, but no solution appeared to take place; on filtering and evaporating to dryness there was no residue.

The material mentioned above as being the final product from the sulphonation of para toluidine, obtained in a yield of twenty grams or ten per cent yield and then uninvestigated, has since been identified as the acid I was looking for, or para toluidine meta sulphonic acid. A small amount was cooled and diazotized in the usual manner; the diazo compound seemed to be insoluble in the amount of water used, for a white crystalline needle-like precipitate appeared. This was decomposed by boiling with dilute nitric acid (Nevile and Winther, loc. cit.), and on cooling small tufts of yellow needles separated. These were filtered off and dried, then recrystallized from alcohol. The best portions of these were then recrystallized from ether and the melting point determined. They melted at 79.5-79.8 (uncorr.). Nevile and Winther gave 79-80, showing that they did not purify their compound. The product is dinitro para cresol, or 3-nitro, 4-hydroxy, 5-nitro toluene.

DIAZOTIZATION OF ORTHO TOLUIDINE SULPHONIC ACID.

Nevile and Winther (loc. cit.), stated that they obtained a diazo compound from their ortho toluidine sulphonic acid and described a few properties, but gave no details of manipulation, so I made several trials to determine the best acceptable method.

Experiment 1.

I suspended some ortho toluidine sulphonic acid in denatured alcohol, and passed in a rapid current of nitrous fumes, generated by dropping concentrated nitric acid into a saturated solution of sodium nitrite, for fifteen minutes. The suspension became slightly warm, and rather pasty at the end. I allowed it to stand a half hour, and at the end of that time it had become very thick and pasty. I then filtered it off by suction, washed with ether, and dried.

Experiment 2.

The procedure used was the same as above using ethyl alcohol in place of denatured alcohol, but for some reason no diazotization appeared to take place. The acid was filtered off and used again.

Experiment 3.

A saturated water solution of the acid was made by boiling some of it up with water, cooling and filtering. No precipitate appeared on passing in nitrous fumes.

Experiment 4.

Some of the acid was dissolved in sodium carbonate solution, sodium nitrite solution added, and after cooling, concentrated hydrochloric acid added drop by drop. Nitrous fumes were given off, but no precipitate appeared.

Experiment 5.

This seems to be the best method and the one employed hereafter in the preparation of all the material subsequently used. The solid ortho toluidine sulphonic acid is suspended in concentrated hydrochloric acid and vigorously stirred. The solution becomes warm and the crystals change in appearance, probably due to the formation of the hydrochloride. The mass is then cooled to 5°, and sodium nitrite solution added slowly with stirring. Immediate reaction takes place, and the mass becomes very pasty as in the first experiment. After obtaining a reaction with starch iodide paper the mixture was allowed to stand a half hour, then filtered by suction, washed with ether and dried. In appearance it was identical with the diazo compound obtained in experiment 1, and can be kept in the same way.

That it was a diazo compound was shown as follows: It was spotted on a piece of filter paper with an alkaline solution of H acid—a red coloration indicates the formation of a red azo dyestuff.

Some of the diazo compound was boiled with dilute nitric acid as described by Nevile and Winther, and a yellowish precipitate of needles obtained, which on recrystallization from denatured alcohol gave light yellow needles of dinitro ortho cresol, (3-hydroxy 3,5-dinitro toluene), melting at 83.5-84° uncorr. (Nevile and Winther gave 85° for the pure substance.) This dinitro compound was obtained in nearly quantitative yield indicating that the diazo compound was presumably pure.

PHYSICAL PROPERTIES OF THE DIAZO COMPOUND

It is almost insoluble in water, and is insoluble in denatured alcohol and ether.

It is a white solid which can be dried and kept without apparent decomposition; it gradually turns pink when exposed to the light for several days, so is kept in a brown bottle if not required for immediate use. It does not explode when struck with a hammer, but deflagrates violently if a flame is brought near or if heated on porcelain.

DECOMPOSITION OF THE DIAZO COMPOUND

(1) With n-Butyl alcohol in the presence of sodium carbonate.

A portion of the dry diazo compound was placed in a flask connected with a reflux condenser, and solid sodium carbonate and n-butyl alcohol added. No reaction took place at ordinary temperature so heat was applied. Decomposition started at 65° and evolution of hydrogen proceeded evenly and smoothly until all the diazo compound had disappeared. The alcohol, at first colorless, became an orange and finally a brown color. The solution was then refluxed an hour to ensure complete decomposition of the diazo compound. The smell of an aldehyde was evident indicating that the hydrogen reaction was taking place; the solution was tested with Schiff’s reagent and with ammoniacal silver nitrate with distinct positive results in both cases, showing aldehyde was present. The alcoholic solution was filtered from the sodium carbonate remaining, and the alcohol distilled off on an oil bath. A yellowish-orange porous solid was left in such a small amount that no derivatives could be made and studied. It was free from the diazo compound, shown by its giving no color with an alkaline solution of H acid.

(2) With n-Butyl Alcohol alone.

The previous experiment showed that n-butyl alcohol would decompose the diazo compound in the presence of sodium carbonate and replace the amino group by hydrogen, so this time a decomposition with the alcohol alone was tried. Decomposition took place evenly and smoothly as before at the same temperature, and the solution became a clear brownish-orange. Aldehyde was given off and tested for as before with positive results. The alcohol was removed by distillation and a thick brownish syrupy liquid was left. This was easily soluble in water, so was dissolved, filtered, and the solution used in the following experiments. At this point it is similar in every way to the solution obtained by Griffin (loc. cit.) from the diazo compound of para toluidine meta sulphonic acid.

Subsequent preparations of this syrup were made in the above way with similar results in every case. The only precaution to be observed is that no part of the flask containing the reaction mixture be allowed to become too hot as the diazo compound is then decomposed violently leaving a grayish ash.

A STUDY OF THE SOLUTION OBTAINED BY THE DECOMPOSITION OF THE DIAZO COMPOUND

The syrup which remained after distilling off the n-butyl alcohol was a thick brown viscous fluid in all cases. It has an acid reaction and is completely soluble in water. On testing it showed the presence of sulphur in quantity and the absence of nitrogen. Some was dissolved in water, filtered, and evaporated on the water bath. After its volume had been considerably reduced it turned a very dark brown, then blackish, and smelled very tarry. It did not crystallize at all, finally becoming very black. To a drop on a watch glass, a drop and then an excess of concentrated hydrochloric acid was added but with no apparent result.

Another portion of the syrup was dissolved in water, boiled with purified animal charcoal, and filtered. The filtrate was colorless. It was then evaporated on the water bath and solidified completely. Some of this solid was ignited and a white ash was left; had it been a sulphonic acid there would have been no residue. A qualitative analysis of the ash was made and much phosphate and calcium found present; therefore this solid was presumed to be a mixture of calcium phosphate from the animal charcoal and perhaps the calcium salt of the sulphonic acid. This showed that animal charcoal could not be used for purposes of purification.

“Activated charcoal” has been advocated for decolorizing solutions as well as for absorbing toxic gases; the author had become acquainted with this material while in the Chemical Warfare Service, and had obtained small samples of “Dorsite” and “Carbonite”. Some of this was powdered and the brown solution boiled with it until most of the color was removed. The solution was then filtered and evaporated on the water bath; a white crystalline solid was again left. Investigation of the activated charcoal showed that concentrated acids extracted some substance which was thrown down in a flocculent white precipitate on making alkaline with ammonia. Therefore another sample of the activated charcoal was boiled with concentrated nitric acid, filtered, and the charcoal washed free from acid; this sample did not decolorize well.

A sample of a specially prepared charcoal for decolorizing purposes manufactured by the Barneby-Cheney Co. was obtained and tried, but was unsuccessful; the color was not removed.

Infusorial earth, kiesel guhr, and “Sil-o-cel” were also tried unsuccessfully; Fullers Earth made a very clear solution but no color was removed.

Some of the brown viscous solution was dissolved in water, the solution filtered and evaporated to a constant volume (estimated when no more vapor could be seen to condense) under diminished pressure (water pump) until it became more brown. It was then allowed to cool, and dry hydrochloric acid gas passed in, first to expel all air or other vapor present, and then under pressure. The solution became slightly warm. A few fine crystals formed on the interior surface of the flask where some of the solution had spattered during distillation, which however were quite indistinct and seemed to be in the center of a drop of water or solution. On allowing the flask to stand over night the whole of the solution seemed to be filled with crystals. They were too indistinct to enable their crystalline form to be determined so an attempt was made to remove some for examination. As soon as they came into contact with the air they disappeared and left a very viscous solution, indicating that they are very hygroscopic. A small amount was removed and placed in a dish in a vacuum desiccator which was evacuated and left for a month, with periodical examinations. No solid appeared at any time.

This is as far as the investigation has been carried at the present time, April twenty-fifth, but its study is being continued.

CONCLUSION

The results of this investigation may be briefly summarized as follows:

(1) Ortho toluidine may be easily converted into its sulphonic acid in which the sulphonic acid group is in the position meta to the methyl group.

(2) Para toluidine is converted into a mixture of two isomeric sulphonic acids of which the one with the sulphonic acid group in the position meta to the methyl group is obtained in a ten per cent yield.

(3) Ortho toluidine sulphonic acid may be easily diazotized using sodium nitrite and concentrated hydrochloric acid.

(4) The diazo compound is very stable.

(5) The diazo compound is easily decomposed with n-butyl alcohol, the hydrogen reaction taking place.

BIBLIOGRAPHY

In addition to the references made in the thesis itself the following authorities have been consulted for the theoretical discussion:

Beilstein, F. C., “Handbuch der organischen Chemie” 1886-1890. Voss, Hamburg.

Victor von Richter, “Organic Chemistry” Trans. 1899-1900. P. Blakiston’s, Philadelphia, Pa. B.P.L. 3974.160

Meyer and Jacobson, “Lehrbuch der organischen Chemie” 1893. Veit & Co., Leipzig. B.P.L. 3973.143

Transcriber’s Note:

Table of contents added by transcriber.

Obvious printer errors corrected silently.

Inconsistent spelling and hyphenation are as in the original.

*** END OF THE PROJECT GUTENBERG EBOOK META TOLUENE SULPHONIC ACID AND RELATED COMPOUNDS ***

Updated editions will replace the previous one—the old editions will be renamed.

Creating the works from print editions not protected by U.S. copyright law means that no one owns a United States copyright in these works, so the Foundation (and you!) can copy and distribute it in the United States without permission and without paying copyright royalties. Special rules, set forth in the General Terms of Use part of this license, apply to copying and distributing Project Gutenberg™ electronic works to protect the PROJECT GUTENBERG™ concept and trademark. Project Gutenberg is a registered trademark, and may not be used if you charge for an eBook, except by following the terms of the trademark license, including paying royalties for use of the Project Gutenberg trademark. If you do not charge anything for copies of this eBook, complying with the trademark license is very easy. You may use this eBook for nearly any purpose such as creation of derivative works, reports, performances and research. Project Gutenberg eBooks may be modified and printed and given away—you may do practically ANYTHING in the United States with eBooks not protected by U.S. copyright law. Redistribution is subject to the trademark license, especially commercial redistribution.

START: FULL LICENSE

THE FULL PROJECT GUTENBERG LICENSE

PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK

To protect the Project Gutenberg™ mission of promoting the free distribution of electronic works, by using or distributing this work (or any other work associated in any way with the phrase “Project Gutenberg”), you agree to comply with all the terms of the Full Project Gutenberg™ License available with this file or online at www.gutenberg.org/license.

Section 1. General Terms of Use and Redistributing Project Gutenberg™ electronic works

1.A. By reading or using any part of this Project Gutenberg™ electronic work, you indicate that you have read, understand, agree to and accept all the terms of this license and intellectual property (trademark/copyright) agreement. If you do not agree to abide by all the terms of this agreement, you must cease using and return or destroy all copies of Project Gutenberg™ electronic works in your possession. If you paid a fee for obtaining a copy of or access to a Project Gutenberg™ electronic work and you do not agree to be bound by the terms of this agreement, you may obtain a refund from the person or entity to whom you paid the fee as set forth in paragraph 1.E.8.

1.B. “Project Gutenberg” is a registered trademark. It may only be used on or associated in any way with an electronic work by people who agree to be bound by the terms of this agreement. There are a few things that you can do with most Project Gutenberg™ electronic works even without complying with the full terms of this agreement. See paragraph 1.C below. There are a lot of things you can do with Project Gutenberg™ electronic works if you follow the terms of this agreement and help preserve free future access to Project Gutenberg™ electronic works. See paragraph 1.E below.

1.C. The Project Gutenberg Literary Archive Foundation (“the Foundation” or PGLAF), owns a compilation copyright in the collection of Project Gutenberg™ electronic works. Nearly all the individual works in the collection are in the public domain in the United States. If an individual work is unprotected by copyright law in the United States and you are located in the United States, we do not claim a right to prevent you from copying, distributing, performing, displaying or creating derivative works based on the work as long as all references to Project Gutenberg are removed. Of course, we hope that you will support the Project Gutenberg™ mission of promoting free access to electronic works by freely sharing Project Gutenberg™ works in compliance with the terms of this agreement for keeping the Project Gutenberg™ name associated with the work. You can easily comply with the terms of this agreement by keeping this work in the same format with its attached full Project Gutenberg™ License when you share it without charge with others.

1.D. The copyright laws of the place where you are located also govern what you can do with this work. Copyright laws in most countries are in a constant state of change. If you are outside the United States, check the laws of your country in addition to the terms of this agreement before downloading, copying, displaying, performing, distributing or creating derivative works based on this work or any other Project Gutenberg™ work. The Foundation makes no representations concerning the copyright status of any work in any country other than the United States.

1.E. Unless you have removed all references to Project Gutenberg:

1.E.1. The following sentence, with active links to, or other immediate access to, the full Project Gutenberg™ License must appear prominently whenever any copy of a Project Gutenberg™ work (any work on which the phrase “Project Gutenberg” appears, or with which the phrase “Project Gutenberg” is associated) is accessed, displayed, performed, viewed, copied or distributed:

This eBook is for the use of anyone anywhere in the United States and most other parts of the world at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg License included with this eBook or online at www.gutenberg.org. If you are not located in the United States, you will have to check the laws of the country where you are located before using this eBook.

1.E.2. If an individual Project Gutenberg™ electronic work is derived from texts not protected by U.S. copyright law (does not contain a notice indicating that it is posted with permission of the copyright holder), the work can be copied and distributed to anyone in the United States without paying any fees or charges. If you are redistributing or providing access to a work with the phrase “Project Gutenberg” associated with or appearing on the work, you must comply either with the requirements of paragraphs 1.E.1 through 1.E.7 or obtain permission for the use of the work and the Project Gutenberg™ trademark as set forth in paragraphs 1.E.8 or 1.E.9.

1.E.3. If an individual Project Gutenberg™ electronic work is posted with the permission of the copyright holder, your use and distribution must comply with both paragraphs 1.E.1 through 1.E.7 and any additional terms imposed by the copyright holder. Additional terms will be linked to the Project Gutenberg™ License for all works posted with the permission of the copyright holder found at the beginning of this work.

1.E.4. Do not unlink or detach or remove the full Project Gutenberg™ License terms from this work, or any files containing a part of this work or any other work associated with Project Gutenberg™.

1.E.5. Do not copy, display, perform, distribute or redistribute this electronic work, or any part of this electronic work, without prominently displaying the sentence set forth in paragraph 1.E.1 with active links or immediate access to the full terms of the Project Gutenberg™ License.

1.E.6. You may convert to and distribute this work in any binary, compressed, marked up, nonproprietary or proprietary form, including any word processing or hypertext form. However, if you provide access to or distribute copies of a Project Gutenberg™ work in a format other than “Plain Vanilla ASCII” or other format used in the official version posted on the official Project Gutenberg™ website (www.gutenberg.org), you must, at no additional cost, fee or expense to the user, provide a copy, a means of exporting a copy, or a means of obtaining a copy upon request, of the work in its original “Plain Vanilla ASCII” or other form. Any alternate format must include the full Project Gutenberg™ License as specified in paragraph 1.E.1.

1.E.7. Do not charge a fee for access to, viewing, displaying, performing, copying or distributing any Project Gutenberg™ works unless you comply with paragraph 1.E.8 or 1.E.9.

1.E.8. You may charge a reasonable fee for copies of or providing access to or distributing Project Gutenberg™ electronic works provided that:

- • You pay a royalty fee of 20% of the gross profits you derive from the use of Project Gutenberg™ works calculated using the method you already use to calculate your applicable taxes. The fee is owed to the owner of the Project Gutenberg™ trademark, but he has agreed to donate royalties under this paragraph to the Project Gutenberg Literary Archive Foundation. Royalty payments must be paid within 60 days following each date on which you prepare (or are legally required to prepare) your periodic tax returns. Royalty payments should be clearly marked as such and sent to the Project Gutenberg Literary Archive Foundation at the address specified in Section 4, “Information about donations to the Project Gutenberg Literary Archive Foundation.”

- • You provide a full refund of any money paid by a user who notifies you in writing (or by e-mail) within 30 days of receipt that s/he does not agree to the terms of the full Project Gutenberg™ License. You must require such a user to return or destroy all copies of the works possessed in a physical medium and discontinue all use of and all access to other copies of Project Gutenberg™ works.

- • You provide, in accordance with paragraph 1.F.3, a full refund of any money paid for a work or a replacement copy, if a defect in the electronic work is discovered and reported to you within 90 days of receipt of the work.

- • You comply with all other terms of this agreement for free distribution of Project Gutenberg™ works.

1.E.9. If you wish to charge a fee or distribute a Project Gutenberg™ electronic work or group of works on different terms than are set forth in this agreement, you must obtain permission in writing from the Project Gutenberg Literary Archive Foundation, the manager of the Project Gutenberg™ trademark. Contact the Foundation as set forth in Section 3 below.

1.F.

1.F.1. Project Gutenberg volunteers and employees expend considerable effort to identify, do copyright research on, transcribe and proofread works not protected by U.S. copyright law in creating the Project Gutenberg™ collection. Despite these efforts, Project Gutenberg™ electronic works, and the medium on which they may be stored, may contain “Defects,” such as, but not limited to, incomplete, inaccurate or corrupt data, transcription errors, a copyright or other intellectual property infringement, a defective or damaged disk or other medium, a computer virus, or computer codes that damage or cannot be read by your equipment.

1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right of Replacement or Refund” described in paragraph 1.F.3, the Project Gutenberg Literary Archive Foundation, the owner of the Project Gutenberg™ trademark, and any other party distributing a Project Gutenberg™ electronic work under this agreement, disclaim all liability to you for damages, costs and expenses, including legal fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH DAMAGE.

1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a defect in this electronic work within 90 days of receiving it, you can receive a refund of the money (if any) you paid for it by sending a written explanation to the person you received the work from. If you received the work on a physical medium, you must return the medium with your written explanation. The person or entity that provided you with the defective work may elect to provide a replacement copy in lieu of a refund. If you received the work electronically, the person or entity providing it to you may choose to give you a second opportunity to receive the work electronically in lieu of a refund. If the second copy is also defective, you may demand a refund in writing without further opportunities to fix the problem.

1.F.4. Except for the limited right of replacement or refund set forth in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.

1.F.5. Some states do not allow disclaimers of certain implied warranties or the exclusion or limitation of certain types of damages. If any disclaimer or limitation set forth in this agreement violates the law of the state applicable to this agreement, the agreement shall be interpreted to make the maximum disclaimer or limitation permitted by the applicable state law. The invalidity or unenforceability of any provision of this agreement shall not void the remaining provisions.

1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the trademark owner, any agent or employee of the Foundation, anyone providing copies of Project Gutenberg™ electronic works in accordance with this agreement, and any volunteers associated with the production, promotion and distribution of Project Gutenberg™ electronic works, harmless from all liability, costs and expenses, including legal fees, that arise directly or indirectly from any of the following which you do or cause to occur: (a) distribution of this or any Project Gutenberg™ work, (b) alteration, modification, or additions or deletions to any Project Gutenberg™ work, and (c) any Defect you cause.

Section 2. Information about the Mission of Project Gutenberg™

Project Gutenberg™ is synonymous with the free distribution of electronic works in formats readable by the widest variety of computers including obsolete, old, middle-aged and new computers. It exists because of the efforts of hundreds of volunteers and donations from people in all walks of life.

Volunteers and financial support to provide volunteers with the assistance they need are critical to reaching Project Gutenberg™’s goals and ensuring that the Project Gutenberg™ collection will remain freely available for generations to come. In 2001, the Project Gutenberg Literary Archive Foundation was created to provide a secure and permanent future for Project Gutenberg™ and future generations. To learn more about the Project Gutenberg Literary Archive Foundation and how your efforts and donations can help, see Sections 3 and 4 and the Foundation information page at www.gutenberg.org.

Section 3. Information about the Project Gutenberg Literary Archive Foundation

The Project Gutenberg Literary Archive Foundation is a non-profit 501(c)(3) educational corporation organized under the laws of the state of Mississippi and granted tax exempt status by the Internal Revenue Service. The Foundation’s EIN or federal tax identification number is 64-6221541. Contributions to the Project Gutenberg Literary Archive Foundation are tax deductible to the full extent permitted by U.S. federal laws and your state’s laws.

The Foundation’s business office is located at 809 North 1500 West, Salt Lake City, UT 84116, (801) 596-1887. Email contact links and up to date contact information can be found at the Foundation’s website and official page at www.gutenberg.org/contact

Section 4. Information about Donations to the Project Gutenberg Literary Archive Foundation

Project Gutenberg™ depends upon and cannot survive without widespread public support and donations to carry out its mission of increasing the number of public domain and licensed works that can be freely distributed in machine-readable form accessible by the widest array of equipment including outdated equipment. Many small donations ($1 to $5,000) are particularly important to maintaining tax exempt status with the IRS.

The Foundation is committed to complying with the laws regulating charities and charitable donations in all 50 states of the United States. Compliance requirements are not uniform and it takes a considerable effort, much paperwork and many fees to meet and keep up with these requirements. We do not solicit donations in locations where we have not received written confirmation of compliance. To SEND DONATIONS or determine the status of compliance for any particular state visit www.gutenberg.org/donate.

While we cannot and do not solicit contributions from states where we have not met the solicitation requirements, we know of no prohibition against accepting unsolicited donations from donors in such states who approach us with offers to donate.

International donations are gratefully accepted, but we cannot make any statements concerning tax treatment of donations received from outside the United States. U.S. laws alone swamp our small staff.

Please check the Project Gutenberg web pages for current donation methods and addresses. Donations are accepted in a number of other ways including checks, online payments and credit card donations. To donate, please visit: www.gutenberg.org/donate.

Section 5. General Information About Project Gutenberg™ electronic works

Professor Michael S. Hart was the originator of the Project Gutenberg™ concept of a library of electronic works that could be freely shared with anyone. For forty years, he produced and distributed Project Gutenberg™ eBooks with only a loose network of volunteer support.

Project Gutenberg™ eBooks are often created from several printed editions, all of which are confirmed as not protected by copyright in the U.S. unless a copyright notice is included. Thus, we do not necessarily keep eBooks in compliance with any particular paper edition.

Most people start at our website which has the main PG search facility: www.gutenberg.org.

This website includes information about Project Gutenberg™, including how to make donations to the Project Gutenberg Literary Archive Foundation, how to help produce our new eBooks, and how to subscribe to our email newsletter to hear about new eBooks.

Table of Contents

- BOSTON UNIVERSITY GRADUATE SCHOOL THESIS META TOLUENE SULPHONIC ACID and RELATED COMPOUNDS Submitted by Charles Francis Hitchcock Allen (A.B., Boston University, 1919) In partial fulfilment of requirements for the degree of Master of Arts 1920

- Table of Contents.

- META TOLUENE SULPHONIC ACID and RELATED COMPOUNDS

- THEORETICAL DISCUSSION

- SULPHONATION OF ORTHO TOLUIDINE

- Experiment 1.

- Experiment 2.

- Experiment 3.

- Experiment 4.

- SULPHONATION OF PARA TOLUIDINE

- DIAZOTIZATION OF ORTHO TOLUIDINE SULPHONIC ACID.

- Experiment 1.

- Experiment 2.

- Experiment 3.

- Experiment 4.

- Experiment 5.

- PHYSICAL PROPERTIES OF THE DIAZO COMPOUND

- DECOMPOSITION OF THE DIAZO COMPOUND

- (2) With n-Butyl Alcohol alone.

- A STUDY OF THE SOLUTION OBTAINED BY THE DECOMPOSITION OF THE DIAZO COMPOUND

- CONCLUSION

- BIBLIOGRAPHY

- Transcriber’s Note:

- THE FULL PROJECT GUTENBERG LICENSE