A boy's text book on gas engines
Date: 2023-10-30T00:00:00+00:00
Keywords: Automobiles -- Motors

The Project Gutenberg eBook of A boy's text book on gas engines

This ebook is for the use of anyone anywhere in the United States and most other parts of the world at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg License included with this ebook or online at www.gutenberg.org. If you are not located in the United States, you will have to check the laws of the country where you are located before using this eBook.

Title: A boy's text book on gas engines
a book for boys describing and explaining in simple language the automobile gas engine

Author: Fay Leone Faurote

Release date: October 31, 2023 [eBook #71991]

Language: English

Original publication: United States: Robert Smith Printing Co, 1908

Credits: Charlene Taylor and the Online Distributed Proofreading Team at https://www.pgdp.net (This file was produced from images generously made available by The Internet Archive/American Libraries.)

*** START OF THE PROJECT GUTENBERG EBOOK A BOY'S TEXT BOOK ON GAS ENGINES ***

Transcriber’s Note

Larger versions of most illustrations may be seen by right-clicking them and selecting an option to view them separately, or by double-tapping and/or stretching them.

Additional notes will be found near the end of this ebook.

The source book did not have a Table of Contents. The one below was created for reader convenience.

INTRODUCTION
THE FOUR-STROKE CYCLE.
THE CYLINDER
VALVES
THE PISTON
THE CRANK SHAFT
THE CONNECTING ROD
THE CRANK CASE
THE CARBURETOR
THE IGNITION SYSTEM
THE COOLING SYSTEM
THE TWO-CYCLE MOTOR.
INDEX

A
BOY’S TEXT BOOK
ON
GAS ENGINES

¶ A Book for Boys Describing and Explaining in Simple Language the Automobile Gas Engine.

By FAY LEONE FAUROTE, B. S. [M. E.]
(Former Instructor Detroit Motor School)

Published by the Author
LANSING, MICHIGAN, U. S. A.

Copyright by
Fay Leone Faurote
1908

ROBERT SMITH PRINTING CO.
CHICAGO—LANSING

PREFACE

Knowing that the motor car is fast becoming the modern form of transportation, both in the social and commercial world, and feeling that the principles of the mechanism which constitutes its propelling power are as yet somewhat of a mystery to the average individual and to “Young America” in particular, the author feels that some of the simple explanations offered in the following pages of this book will be welcomed and appreciated. While they do not cover the entire subject, it is hoped that they may tend to shed some light, and in a way make understandable the construction and operation of the automobile gas engine.

FAY L FAUROTE.

November 25, 1907.

A Four-cylinder Motor, so sectioned that it shows interior of cylinder, valves, piston, crank shaft and connecting rods.

A BOY’S TEXT BOOK
ON GAS ENGINES

INTRODUCTION

Boys, when I was a small boy, I remember how much I was interested in everything which was mechanical. The engineer was my hero; the solving of the mysteries of an engine and the learning how to drive one, was my ambition.

I remember well how I tried to read the dry, technical description of motors, steam engines and such things. I remember, too, how hard it was to understand those books; how the various technical terms used to bother me, until at last, in despair, I would throw the books aside. It seemed as if the men who wrote them never realized that boys existed,—that boys wanted to know about such things.

At other times how glad I was when I found a good-hearted engineer who seemed to know and understand my feelings and my desire to learn. How easy it was to comprehend his explanations, because he used homely, everyday things to illustrate his meaning. He made you forget there was anything complicated about machinery. He simply took up one part at a time, and when he had finished with it, everything was as plain as the nose on your face.

Boys, then and there I decided that if I ever did understand some of these seeming mysteries of engineering, I would write a book that boys could understand. I would write it so that they couldn’t help it, it would be so plain; there would be no secrets; they should know all about it, and what is more, should be able to reason it all out for themselves.

Fig. 1—The Essential Parts of a Gas Engine.

Let me tell you about each part separately. After we have gone over each part you will find that you will understand the action of the motor and other parts of the car well enough so that you will unconsciously reason it all out for yourselves. Some of the descriptions and explanations may at first seem unsatisfactory, but I think with a little thought and study you will be able to master them in a short time. I want your confidence, boys, and then I know we will get along all right together.

Fig. 2—A Single-cylinder Horizontal Engine. Note location of valves in this type.

Suction Stroke      Compression Stroke      Working Stroke      Exhaust Stroke

Fig. 3—Four views of a section of a Vertical Cylinder, showing position of valves, pistons and cams for the four different strokes.

THE FOUR-STROKE CYCLE.

This subject looks like a bugbear, doesn’t it. Well, it is one of the first things of which we shall have to dispose, and so we’ll tackle it right away. We will start backwards, and take the word cycle first. If you will look in the dictionary you will find that this word means “a circle or orbit; an interval of time in which a succession of events is completed, and then returns in the same order.”

Suction Stroke
Compression Stroke
Working Stroke
Exhaust Stroke

Fig. 4—A Four-cycle Diagram, showing sequence of strokes in this type of motor.

This does not mean very much to you, does it? Well, let us go into it a little farther. Supposing you were running relay races around a block; you would run down on one side, across on another, back on the other side, and then back to the starting point, wouldn’t you? You would have completed a cycle then because you have taken a “certain time in which a succession of events (streets) has been completed” and you are back again at the start ready to “return in the same order.”

Fig. 5—Drawing showing comparison between gas engine and a cannon connected with a grindstone.

There is not anything complicated about that, is there? In other words just change the four-stroke cycle to a four-street circle, and this will help you to keep in mind the meaning of this term. Do you remember last Fourth of July when you had your cannon out, how many things you had to do to fire it, or in other words to complete the cycle of operations. You did four things, didn’t you?

No. 1. You put in the powder.
No. 2. You rammed it in with a ramrod.
No. 3. You fired it by touching a match to it.
No. 4. You cleaned it out.

You had gone around your four-sided circle, and were back again, at the start, ready to do the same things over again. You were running a gas engine then, only you did not realize it.

Let us assume for the sake of argument, that you had a bullet in your cannon, and that to this bullet was connected a rod which had its other end fastened to the crank of a grindstone. Then if the barrel of the cannon was long enough, and the rod which connected the bullet and crank was short, the bullet could not get out of the cannon barrel, could it? It would therefore have to go back and forth very much like the pedal on a grindstone does. Of course the rod and the crank would have to be very strong in order to keep the bullet in, but we will assume that they are, and that the bullet must travel back and forth inside the barrel. Now, if the bullet is going to stay in the barrel we must provide some way to load the cannon, and also to clean it out, therefore we will cut two holes in the end, one at I and one at E, and then instead of using powder suppose you use some explosive gas which will not leave so much soot behind it. You know how a squirt gun works—how you draw the water in by pulling out the plunger, and how you force the water out again by pushing it in again.

Fig. 6.

Let us work the cannon the same way. Let us call the farthest point to which the bullet travels going in “H” and the farthest point to which it travels going out “K.” Now let us assume that the bullet is at “H,” and that it is just starting out in the direction of “K.” If we open the hole “I” in the side of the cannon by taking out the plug “L,” and put a hose, connected with our gas tank, in there, then the outward motion of the bullet “P” will pull the cannon full of gas, won’t it? Before the gas has a chance to escape we will put in the plug “L” again. Now we have the cylinder full of gas, but as the bullet is at the end of its stroke, and cannot go any further, we will have to push the gas together again and get the bullet into position “H.” This will be a good thing for the gas, because it will crowd the particles of it closer together, and make it explode quicker, so we will do this. Of course, in order to keep the gas in there we have had to close up the touch-hole of the cannon, but now that we are ready to fire it, we will take this plug out, and touch a match to the gas. An explosion follows, and the bullet travels from the position “H” to the position “K.” All this time the crank of the grindstone must have been turning because the bullet and the crank are fastened together, and therefore, instead of traveling through the air, the bullet has used up its energy in turning the grindstone. When you get a grindstone started it is rather hard to stop, isn’t it? And if you didn’t stop it, it would keep on turning around, wouldn’t it? If this is true, we might as well let it clean the cannon. As the hole “I” is connected with the gas tank, we cannot let it force the burnt gas out there, can we? We will therefore pull out the plug “J” in the hole “E” just as the bullet reaches the point “K” so that in coming back it will force the burnt gases and smoke out through the hole “E.” Now we are all ready to start over again; the cannon has been cleaned out, and the bullet still being fastened to the grindstone, which is turning, as a result of the explosion, would immediately begin starting out on another outward stroke. If we put in the plug “J” again and pull out the plug “L,” the bullet or piston as we might call it now, will suck in another charge of gas.

Fig. 7—Grinding a valve.

Fig. 8—A section of a Cylinder showing location of various parts—end view.

You can see that if you had two boys, one of them to pull out the plugs, and another to fire the charge you could keep the gun firing steadily, and run the grindstone. After you have done this for a while you will get tired of taking out the plugs and putting them in, and standing there with a match lit all the time, and you would wish there was some way to make the grindstone, which was running, do all this for you. This is exactly what happened to some of the old engineers, and so they set about trying to accomplish this result. They succeeded in rigging a piece of machinery that would open and close these holes automatically, and with the introduction of electricity they also devised a way whereby the charge could be ignited by an electric spark instead of a match. The plugs which cover the holes, they called valves and the plug which contained the electric wires, used for firing the gas, they called a spark plug.

Now let us see what we have learned in this chapter. We have found that it takes four strokes to explode one charge of gas

1. Suction stroke, during which the gas is sucked into the barrel of the cannon, or cylinder as it is called.

2. The compression stroke, during which the gas is compressed so that it will burn easier.

3. The explosive stroke, or working stroke, called so on account of the fact that the explosive force of the gas is used to turn the wheel.

4. The cleansing, or exhaust stroke, during which the burnt gas and smoke is forced out of the barrel.

For this reason, a gas engine which works on this principle is called a Four-Stroke Cycle Engine. It requires four strokes to complete the entire operation and bring it back to the beginning ready to start over again.

THE CYLINDER

So far we have confined ourselves to the parts of a cannon, but now that we are going to take up the study of the motor in its details let us call them by their regular names. The barrel of the cannon we will call a cylinder. In an actual motor a cylinder is made out of cast iron, carefully bored out inside, so that the hole is perfectly round, and the sides of the wall as smooth as possible.

Fig. 9.

You will realize that this is necessary as we want to reduce, as much as possible, any rubbing or friction, as it is called, between the piston and cylinder walls. Next we must provide some means of cooling these walls, as you know that the continuous firing would soon make them very hot. This is done by surrounding the cylinder with what is known as a water jacket through which water can be circulated, thereby carrying off the heat, and keeping the iron from getting red hot. We must also cut two holes in the side of the cylinder to make places for the valves and a place for the spark plug.

Fig. 10—End view of Horizontal One-cylinder Motor, showing piston, valves and valve mechanism.

A cylinder is generally mounted on its side in a one cylinder engine, and is set up on end when it is desired to use more than one. Therefore, in a one cylinder motor you will notice that the piston moves back and forth, whereas in a two-cylinder, four-cylinder or six-cylinder type, the pistons move up and down. As far as the action of the parts is concerned they work in exactly the same way, only that the valve mechanism has to be changed somewhat.

The cylinder is bolted to a framework called the crank case which furnishes a solid foundation upon which it can rest.

VALVES

You will remember that in first discussing the drawing in and cleaning out of the gas that two holes had to be cut in the sides of the cylinder wall. One of these through which the fresh gas might be sucked in, and the other through which the burnt gas might be expelled. Also remember that we kept these holes plugged except when it was necessary to have them open to perform their work.

Fig. 11—The evolution of a Valve.

Fig. 12—A regular Valve.

Now let us take a section of a valve and see how it is made up. You will notice first the little plug “A” which covers the hole in the cylinder; it is tapered very much like a glass stopper in a bottle for the reason that in this form it is easier to fit it to the opening; it can be “ground in” in the same way that a glass stopper can, in order to make an air-tight fit. “B” is a rod known as the valve stem, and is simply a round piece of steel fastened to the valve plug “A.” “S” is a valve spring which holds the valve down into the cylinder wall, or valve-seat, as it is called. In order to open these valves you can see that all that is necessary for you to do is to push up on the valve stem “B.” This will raise the valve “A” away from its seat into the position shown by the dotted lines, leaving a space all around through which the gas may enter or leave. In an actual motor, however, little irregular pieces of steel, cut out in general shape shown in Fig. 14 perform the operation of raising the valve.

Fig. 13—Three positions of a Valve Cam.

Fig. 13 shows three positions of one of these revolving pieces of steel, technically called cams, first, in the act of just starting to raise the valve; second, its position when the valve is entirely open; third, its position when the valve has just closed. If both valves are operated by these cams you can see that if they are set at the proper position they can be opened at different times and entirely independent of each other. If you will look at Fig. 3 you will see a complete motor, the inlet valve on the left side, and the exhaust valve on the right side. This figure will also show you the little cams in their various positions at different points of the four strokes. Sometimes the two valves, instead of being on opposite sides of the cylinder, are placed on the same side, and both cams are put on the same shaft, which, by the way, is called a cam-shaft.

Fig. 14—Names of Valve Parts.

Fig. 14 shows two such valves, the left hand one opening, and the right hand one closed. The extreme left hand view shows the way they would look if viewed from the end. It also gives you the names of all the parts.

Fig. 7 shows how the valves are “ground in.” The way you do it is to take the valve out, and coat it with very fine emery dust and oil, and then put it back in place leaving off the spring, fit a wrench to it on top as shown in the picture and twirl it around as you would a glass stopper in a bottle until it is perfectly air-tight, after which the valve should be removed and both it and the valve seat carefully wiped off so that none of the emery will get into the cylinder or other working parts of the engine and cause them to be cut.

There are several different ways of making valves and several places to put them so that you must not always expect to find them in the same place. Their action is the same, however, no matter where they are situated or how they are operated, and I think with a little examination and study you will always be able to find them and understand how they work in any engine.

THE PISTON

The piston forms, as you will recall, the bullet in the cannon, which instead of leaving the barrel, was made to travel back and forth inside of the cylinder under the action of the explosive gas. Owing to the fact that a solid piece of iron would be very heavy and would get very warm, the real piston used in a motor is made hollow so that it is merely a shell. Instead of fastening the rod to the end of it, a small rod, called the piston pin is in the center of it, and to this the connecting rod is connected. Fig. 16 shows a section of the piston. You will notice that the piston pin is kept from sliding sideways by a bolt that is screwed into it.

Fig. 15—A Piston, Piston Ring, and Piston Pin.

Owing to the fact that both the cylinder walls and piston get hot, and that iron expands and contracts according to its temperature, it is not possible to make a piston alone which would remain air-tight all the time. Engineers, therefore, found it necessary to put rings, which were cut at some point in their circumference, on the outside of the piston itself. These piston rings, due to the fact that they are cut, can accommodate themselves to the varying diameters of the cylinder, and can therefore keep an air-tight fit, even when the piston is moving back and forth all the time. Most of you, no doubt, know that the plunger in a pump is made air-tight by one or a set of leather washers, which, owing to their pliable structure, can expand or contract so as to always fit air-tightly the pipe in the pump. Piston rings work in precisely the same manner, and are always kept lubricated so that they will work smoothly, thus doing away with any friction which might result.

Fig. 16—A section of a Piston, showing location of piston pin and end of connecting rods.

THE CRANK SHAFT

Most of you are familiar with a crank as applied to a grindstone. A crank in a motor is practically the same shape except that it is supported on two bearings instead of one and is therefore made in the form shown in Fig. 17. The crank shafts for two and four-cylinder motors are only a combination of two or four of these single cranks. Crank shafts are made up of steel, carefully forged, and then turned and ground down to proper size to fit the bearings for which they are intended. They are hardened and every precaution taken to keep them from wearing. They form one of the most important parts of the motor because they change the back and forth motion of the piston into the rotary motion of the fly wheel. The fly wheel in our former illustration was represented by the grindstone itself. In the real motor the fly wheel is made of cast iron, and after being carefully balanced so that it turns evenly, it is securely bolted to the crank shaft, so that they practically form one piece.

Fig. 17—A Four-cylinder Crank Shaft.

THE CONNECTING ROD

The connecting rod, as you can guess from its name, forms the connecting link between the piston and crank shaft, transferring the energy of the explosive gas, acting behind the piston, to the crank shaft and fly wheel, from which it can be transmitted to the driving wheels of the automobile. It is made up in some such form as shown in Fig. 18 and is made of steel or bronze. It has a bearing at each end, the smaller one fitting around the piston pin, the larger one surrounding a portion of the crank shaft called the crank pin. Both of these bearings are lubricated by oil which splashes up from the bottom of the crank case when the engine is running. You will notice that one of the bearings is cut in two and bolted together so that you can take it off from the crank shaft, should you wish to examine it.

Fig. 18—A typical Connecting Rod.

Fig. 19—The two halves of the Connecting Rod Bearing.

THE CRANK CASE

The crank case of a motor serves as a foundation for the engine, furnishes a support for the main bearings in which the crank shaft revolves and encloses the working parts in such a way as to provide for their lubrication and protect them from the dust and other substances which might materially hinder the proper performance of their functions. To a certain extent the crank case might be compared to the framework of the grindstone, although the latter does not answer as many purposes as the real crank case of the motor does.

Fig. 20—The two halves of a Four-cylinder Crank Case.

The case itself is made of iron or aluminum, and is so put together that, although practically air-tight, there is still a means provided for getting inside of it for examination of the working parts or an adjustment of the bearings.

THE CARBURETOR

The carburetor or mixing chamber, as it is sometimes called, is a device used for obtaining an explosive mixture of gasoline and air. It consists, as shown by the accompanying drawing, of two principal parts, an air pipe and gasoline pipe, the latter running through the wall and discharging into the center of the former.

Fig. 21—Simple drawing of a Carburetor.

In order to make sure that the amount of gasoline flowing out of the gasoline jet shall be just the right amount at all times it is necessary to provide a little gasoline tank, which forms a part of the carburetor casting itself, which is known as a float chamber, so that the amount of gasoline in the main tank will not affect the amount discharged at the nozzle. You can see why this is necessary if you think of a water tank or a dam. If the water was almost up to the top of the dam and you should bore a hole through the wall somewhere near the bottom, the water would flow out faster than if the water was low. By putting this little gasoline tank in the carburetor itself and keeping a certain height of gasoline in this smaller reservoir, which always automatically shuts off the supply at the right time, you can make the pressure, and therefore the flow of the liquid, always the same. The illustration will show this plainly. For instance, when the gasoline gets low the little float will gradually drop down until the ball on the end of the float stem will open the valve in the gasoline pipe. The gasoline will then flow in from the tank until the proper amount has filled the float chamber and caused the float to bob up to its former position, carrying the ball, which closes the gasoline off, up with it. By this means the requisite amount of gasoline is always kept in the float chamber.

The amount of air entering the mixing chamber is controlled by changing the size of the hole through which the air enters and the quantity of gasoline admitted is regulated by means of a needle valve in the gasoline pipe.

Although many carburetors, in fact most of them, do not look like this drawing, yet their action is the same, and by careful study you will find that the same principles enter into their construction. Fig. 22 shows an actual sectional drawing of a carburetor used on a four-cylinder motor. In this particular carburetor, however, the float chamber and float surround the mixing chamber, and the float valve, instead of being directly under the float, is at the right hand side and is operated by means of a lever. The needle valve, which is the little round rod having a “T” handle, running up through the center of the mixing chamber, controls the amount of gasoline flowing from the gasoline chamber to the nozzle. The air comes up through the bottom and around the gasoline jet. At the left you will notice a small valve which opens downward, which you do not find on the other carburetor. It is known as an auxiliary air valve and allows a certain amount of air to be added to the mixture, a small quantity of which is sometimes needed to keep the mixture just right. The throttle valve, which looks like a damper in a stovepipe and which controls the amount of gasoline vapor going in to the engine, will be seen in the upper pipe.

Fig. 22—A Typical Four-cylinder Carburetor.

THE IGNITION SYSTEM

The ignition system is the name applied to the batteries, coils, commutator and spark plug which, acting as a whole, produce an electric spark hot enough and at the right time to fire the charge in the cylinder. There are three ways in which an electric current may be obtained which have been found to be of practical use in automobile construction. First, by a dry battery; second, by a storage battery; and third, by magneto or dynamo. You can look up the construction of these things in any good book on electricity, so that I will not explain them further here. As the object of the whole system is to produce a sufficiently hot spark to fire the mixture at the right time, it is sometimes necessary to raise the pressure of the electric current. When either a dry battery or storage battery or a certain type of magneto is used, it is necessary to put it through what is known as an induction coil in order to raise the pressure so it will be high enough to jump across the two points in the cylinder.

An induction coil consists merely of a bundle of soft wires around which is wound two separate coils of wire. The first, known as the primary winding, is of coarse wire, and the second, known as the secondary winding, is of fine wire. When the current flowing through the primary coil is rapidly made and broken, another current of very high voltage is created in the secondary circuit.

Fig. 23—Wiring Diagram, showing electric circuit for one cylinder. The sketch is only diagrammatic—not a reproduction of any actual wiring system.

When the current starts to flow through the primary winding, the bundle of wires immediately becomes a magnet and attracts the vibrator. As soon as this occurs, however, the flow of the current is interrupted and the vibrator resumes its former position and the action is repeated. Thus you can see that the coil automatically makes and breaks its own circuit. The rapidity with which this is done may be changed at will by adjusting the vibrator screw.

Fig. 24—The Four-cylinder, Four-cycle Diagram, showing the order in which the various cylinders do their work.

Having thus obtained an electric current of sufficient strength to fire the mixture it is necessary to supply a device which will automatically open and close the electric circuit at the proper time. Such a device is called a commutator and consists of two parts; one a rotating part, actuated by the engine, which makes a metallic contact with one or more points on a stationary part, the points being so located that contact occurs at the proper time for igniting the charge in any particular cylinder.

Fig. 25—Four-cylinder Wiring Diagram.

In the four-cylinder wiring diagram (Fig. 25) various parts of an ignition system may be easily seen. The electric current is furnished either by a set of dry cells or by a storage battery. Four individual coils and a four point commutator are used. The commutator is driven by means of bevel gears from the engine itself. A single switch controls the whole circuit, it being provided with two points, making it possible for either battery to be used at will.

Fig. 26—Types of Spark Plugs.

Fig. 27—A Single Cylinder Commutator. Diagrammatic sketch.

Fig. 28—A Two-point Switch.

Fig. 29—A Four-cylinder Commutator.

Fig. 30—A Two-cylinder Commutator.

THE COOLING SYSTEM

In order to prevent the walls of the cylinder from becoming red hot, it is necessary to cool them by some means, and this is done by surrounding the cylinder with a water jacket through which the cooling water is circulated.

Fig. 31—A Diagram showing piping and direction of circulation in a One-cylinder Water-cooled Motor.

In order to prevent the water from boiling and evaporating, thus making the constant addition of water necessary, a radiator is introduced into the system. This radiator is made up of very thin tubes which give up their heat rapidly, thereby keeping the temperature of the water below the boiling point. A fan is also used sometimes to draw the air through between the tubes, thereby making the process of cooling take place more rapidly. The system is so arranged that the water is drawn from the lower part of the radiator where the water is coldest by means of a pump and forced up through the water jackets and back into the radiator again. Several different styles of pumps are used, but a very common one is the gear pump shown in Fig. 32. As you will see by the drawing, it consists of two gears en mesh with each other which revolve in the direction indicated by the arrow. The water entering through the inlet pipe is drawn around the outside and forced out through the outlet at the top.

Fig. 32—A Gear Water Pump.

Fig. 33—Front End of Motor, showing radiator, fan and cam shaft gears.

Fig. 34—A typical Radiator.

Fig. 35—Valve side of a Four-cylinder Motor.

Fig. 36—Opposite side of same Motor showing Carburetor and Inlet Pipe.

Fig. 37—Bottom view of same Motor with oil pan removed showing Crank Shaft, and Connecting Rods.

Fig. 38—Top view of same Motor showing Valve Caps and Holes for Spark Plugs.

NOTE—Both views show motor mounted in ring frames used for assembling in factory.

THE TWO-CYCLE MOTOR.

Although the four-stroke cycle type of motor is used by most of the automobile manufacturers, yet there is another type which has given such good results that it is destined to become one of the important forms to be used in gas engine vehicle manufacture.

Fig. 39.

It therefore merits a brief description. It has the advantage of being very simple in construction and operation, and for this reason it has become very popular among the marine engine builders, although with a few exceptions it has not as yet been accepted by motor car engineers. It is called a Two-stroke Cycle Motor, so named because it combines in two strokes the series of changes ordinarily accomplished in four in the four-stroke cycle type. Its operation may be seen by referring to the accompanying diagrams. It is first assumed that the engine is being turned over by hand in the direction indicated by the arrow. You will note that as the piston moves up it will uncover a port (H), allowing the gasoline vapor from the mixing chamber to enter the crank case. As soon as the piston moves down again, a port (J) will be opened, allowing the mixture which has just been compressed to rush through a “by-pass” (F), into the “combustion chamber,” or upper part of the cylinder. Now, as the piston moves up again on the next stroke, this charge is compressed still more, then as the piston reaches its uppermost position the charge is ignited and the engine begins to work under its own power. The gases continue to act on the piston until nearly the end of the stroke is reached, when you will notice, by referring to the drawing, the exhaust port (G) is passed. At this point the burned gases rush out into the air. You will also notice that in order to aid the discharge and fill the cylinder again, as the piston travels a little farther down, the inlet port will be again uncovered, and the next charge, which has meanwhile been taken into the crank case and compressed, will enter the cylinder, forcing the exhaust gases out.

Fig. 40.

In order to prevent the vapor which has just entered the cylinder from traveling straight across and out through the exhaust port, thus wasting a portion of the fuel, a “baffle plate” (K) is cast on top of the piston which deflects the gases toward the top of the combustion chamber, producing a sort of whirling action which tends to scavenge the cylinder most thoroughly. In order to prevent the burning gases from traveling back into the crank case and igniting the gas there, thus producing a “back explosion,” a wire gauze (S) is placed in the “by-pass.” You will note that this type of motor has no valves, no cams and no cam shaft, in fact, its simplicity is such that it practically cannot get out of adjustment. It therefore is a form of gas engine which as soon as engineers are able to educate the public to its peculiarities bids fair to become as popular and practical as the four-stroke cycle.

INDEX

Cam shaft | 21
Cam | 20
Carburetor | 28
Commutator | 33
Connecting rod | 26
Connecting rod—lubrication of | 26
Cooling system | 37
Crank case | 27
Crank shaft | 25
Cycle—explanation of four-stroke type | 9
Cycle—explanation of two-stroke type | 42
Cylinder | 16
Electrical ignition | 31
Exhaust valve | 21
Fan—radiator | 39
Float chamber | 28
Gasoline valve | 30
Ignition | 31
Induction coil | 32
Inlet valve | 21
Piston pin | 24
Piston ring | 24
Piston | 23
Pump—water | 38
Radiator | 39
Spark plug | 35
Switch—electric | 36
Valve grinding | 21
Valves | 19
Valves—mechanism | 21
Water cooling system | 37
Water pump | 38
Wiring diagram—four-cylinder | 34
Wiring diagrams—single-cylinder | 32

ANOTHER BOOK BY THE SAME AUTHOR

A bigger and more comprehensive work
on the same subject.

“The How and Why of the Automobile”

Did you ever read a book which gave you just the information you wanted without being compelled to go through page after page of introduction and history?

¶ Did you ever talk to a man who came over on your side of the fence and talked WITH you and not AT you—who explained things in such a way that you laughed at yourself afterwards for not understanding the subject before—it was really so simple?

¶ Do you remember when you used to study by outlines—how difficult problems unfolded themselves—how the logical sequence of facts seemed to make what you expected to find hard, readily understandable?

¶ Do you remember the innumerable times you have said to yourself “If I only had somebody here to explain things—someone who would go through this proposition with me until I understood it—someone who would use homely and familiar examples to explain things, instead of talking over my head by using technical terms?”

¶ The author realized all these difficulties himself, because he has been through it all. Not only that, but his experience as an instructor of a large motor school taught him the way to explain the various parts of a motor vehicle in simple language, so that even the boy of fifteen could understand and appreciate them.

¶ For instance, did you ever think that the physician uses a form of carburetor whenever he gives chloroform or ether—do you realize that a shotgun is a form of gas engine whose action is almost identical with that of an automobile motor?

¶ Do you want to know what a sliding gear transmission is—explained in such simple language that anyone can understand it?

¶ Would you like to see what’s inside of an automobile engine—would you like to know the name of every part—be able to talk intelligently about it and be your own mechanic—tell your chauffeur what to do—know when he is bluffing you?

¶ In a word, would you like to know all about a motor car—how it works—how to drive it and how to take care of it? Then subscribe for a copy of

“THE HOW AND WHY OF THE AUTOMOBILE”
By FAY L. FAUROTE
PRICE, $1.00 PREPAID

Don’t delay—send in your order to-day. Get the complete story of a motor car—the advanced course of which the book you have just finished is only the beginning.

Address,
Motor Text Book Dept. ROBERT SMITH PTG. CO., Lansing, Mich., U. S. A.

“THE HOW AND WHY OF THE AUTOMOBILE”

A book of practical information for seekers after the fundamental facts regarding the gasoline engine and its application to the motor car.

Interesting and instructive to both the beginner and the expert—the former for information, the latter for reference.

Written by Fay L. Faurote, B. S. (M. E.), for five years closely associated with the Experimental Department of a pioneer automobile factory, for two years instructor in the Detroit Motor School.

The book, which is handsomely bound in full cloth, printed on high-grade enameled paper, contains over 200 pages and 250 illustrations and covers the following subjects:

CONTENTS

General Theory of Gas Engines—Simple explanation of cycle—The four-stroke cycle—The two-stroke cycle—Advantages and disadvantages of each.

Motor Design—Cylinder, what it is and its use. Valves, mechanical and automatic—Forms of valves—Valve timing and its influence on the motor—Valve grinding, how to do it—Valve nomenclature. Crank Case—The construction Bearings—Accessibility—Working parts—Uses. A crank case oiling system. Crank Shafts—What they are—One, two, four and six-cylinder crank shafts—Crank case diagram, showing instantly conditions in all cylinders—Diagram showing firing points and sequence of same. Connecting Rods—Construction and material—Bearings and lubrication. Pistons—Piston rings—Piston pins.

The Carburetor—A very simple explanation of carburetion—The mixing valve—A few of the first types—Some of the modern carburetors—Foreign carburetors.

Ignition—The make and break system—A simple explanation of the apparatus used. The Jump Spark System—Electrical units. Sources of Electricity—The dry cell—The storage cell—Dynamos and magnetos—The spark coil—Commutators and timing devices—Spark plugs—Wiring diagrams.

Cooling System—Air Cooling. Water Cooling—Direction of circulation—Radiators—Water pumps—Fans—Anti-freezing solutions.

The Transmission—Reason for and use of transmission. Simple Explanation of Action—Individual clutch type—The sliding gear—The three speed progressive—The three speed selective—The four speed selective—Planetary gear—Friction drive.

Methods of Driving—Single chain drive—Double chain drive—Bevel gear drive.

Running Gear—Front Axle—Construction of—Steering Gear. Rear Axle—Differential gear—The live axle—The dead axle—Wheel construction—Bearings.

Horse Power Determinations—Engine testing—Indicated horse power—Brake horse power—Mechanical and heat efficiency—Road testing.

What a Prominent Trade Paper Says About It.

A Handbook of Practical Value—The latest addition to the popular type of automobile handbook. “The How and Why of the Automobile,” by Fay L. Faurote, fulfills what its author has set himself to achieve, namely, to present a plain, easily understood description of the modern automobile. Assuming that his reader knows nothing about the subject, the author introduces the automobile in as simple and untechnical a manner as possible. The entire field is covered and covered so completely that the work can be recommended as a handbook for beginners or those with only a limited knowledge of this subject.—Automobile, April 18.

Send in your order at once—don’t delay. The price is $1.00 postage pre-paid, and the address is

Motor Text Book Dept., ROBERT SMITH PTG. CO., Lansing, Mich., U. S. A.

Transcriber’s Notes

Punctuation, hyphenation, and spelling were made consistent when a predominant preference was found in the original book; otherwise they were not changed.

Simple typographical errors were corrected; unbalanced quotation marks were remedied when the change was obvious, and otherwise left unbalanced.

Illustrations in this eBook are shown as close as possible to their original positions in the printed book, so several of them actually are mid-paragraph. This was done because some of them are referenced only by their content, not by their names.

The index was not in good alphabetical order; Transcriber re-sorted it. It was not checked for correct page references.

*** END OF THE PROJECT GUTENBERG EBOOK A BOY'S TEXT BOOK ON GAS ENGINES ***

Updated editions will replace the previous one—the old editions will be renamed.

Creating the works from print editions not protected by U.S. copyright law means that no one owns a United States copyright in these works, so the Foundation (and you!) can copy and distribute it in the United States without permission and without paying copyright royalties. Special rules, set forth in the General Terms of Use part of this license, apply to copying and distributing Project Gutenberg™ electronic works to protect the PROJECT GUTENBERG™ concept and trademark. Project Gutenberg is a registered trademark, and may not be used if you charge for an eBook, except by following the terms of the trademark license, including paying royalties for use of the Project Gutenberg trademark. If you do not charge anything for copies of this eBook, complying with the trademark license is very easy. You may use this eBook for nearly any purpose such as creation of derivative works, reports, performances and research. Project Gutenberg eBooks may be modified and printed and given away—you may do practically ANYTHING in the United States with eBooks not protected by U.S. copyright law. Redistribution is subject to the trademark license, especially commercial redistribution.

START: FULL LICENSE

THE FULL PROJECT GUTENBERG LICENSE

PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK

To protect the Project Gutenberg™ mission of promoting the free distribution of electronic works, by using or distributing this work (or any other work associated in any way with the phrase “Project Gutenberg”), you agree to comply with all the terms of the Full Project Gutenberg™ License available with this file or online at www.gutenberg.org/license.

Section 1. General Terms of Use and Redistributing Project Gutenberg™ electronic works

1.A. By reading or using any part of this Project Gutenberg™ electronic work, you indicate that you have read, understand, agree to and accept all the terms of this license and intellectual property (trademark/copyright) agreement. If you do not agree to abide by all the terms of this agreement, you must cease using and return or destroy all copies of Project Gutenberg™ electronic works in your possession. If you paid a fee for obtaining a copy of or access to a Project Gutenberg™ electronic work and you do not agree to be bound by the terms of this agreement, you may obtain a refund from the person or entity to whom you paid the fee as set forth in paragraph 1.E.8.

1.B. “Project Gutenberg” is a registered trademark. It may only be used on or associated in any way with an electronic work by people who agree to be bound by the terms of this agreement. There are a few things that you can do with most Project Gutenberg™ electronic works even without complying with the full terms of this agreement. See paragraph 1.C below. There are a lot of things you can do with Project Gutenberg™ electronic works if you follow the terms of this agreement and help preserve free future access to Project Gutenberg™ electronic works. See paragraph 1.E below.

1.C. The Project Gutenberg Literary Archive Foundation (“the Foundation” or PGLAF), owns a compilation copyright in the collection of Project Gutenberg™ electronic works. Nearly all the individual works in the collection are in the public domain in the United States. If an individual work is unprotected by copyright law in the United States and you are located in the United States, we do not claim a right to prevent you from copying, distributing, performing, displaying or creating derivative works based on the work as long as all references to Project Gutenberg are removed. Of course, we hope that you will support the Project Gutenberg™ mission of promoting free access to electronic works by freely sharing Project Gutenberg™ works in compliance with the terms of this agreement for keeping the Project Gutenberg™ name associated with the work. You can easily comply with the terms of this agreement by keeping this work in the same format with its attached full Project Gutenberg™ License when you share it without charge with others.

1.D. The copyright laws of the place where you are located also govern what you can do with this work. Copyright laws in most countries are in a constant state of change. If you are outside the United States, check the laws of your country in addition to the terms of this agreement before downloading, copying, displaying, performing, distributing or creating derivative works based on this work or any other Project Gutenberg™ work. The Foundation makes no representations concerning the copyright status of any work in any country other than the United States.

1.E. Unless you have removed all references to Project Gutenberg:

1.E.1. The following sentence, with active links to, or other immediate access to, the full Project Gutenberg™ License must appear prominently whenever any copy of a Project Gutenberg™ work (any work on which the phrase “Project Gutenberg” appears, or with which the phrase “Project Gutenberg” is associated) is accessed, displayed, performed, viewed, copied or distributed:

This eBook is for the use of anyone anywhere in the United States and most other parts of the world at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg License included with this eBook or online at www.gutenberg.org. If you are not located in the United States, you will have to check the laws of the country where you are located before using this eBook.

1.E.2. If an individual Project Gutenberg™ electronic work is derived from texts not protected by U.S. copyright law (does not contain a notice indicating that it is posted with permission of the copyright holder), the work can be copied and distributed to anyone in the United States without paying any fees or charges. If you are redistributing or providing access to a work with the phrase “Project Gutenberg” associated with or appearing on the work, you must comply either with the requirements of paragraphs 1.E.1 through 1.E.7 or obtain permission for the use of the work and the Project Gutenberg™ trademark as set forth in paragraphs 1.E.8 or 1.E.9.

1.E.3. If an individual Project Gutenberg™ electronic work is posted with the permission of the copyright holder, your use and distribution must comply with both paragraphs 1.E.1 through 1.E.7 and any additional terms imposed by the copyright holder. Additional terms will be linked to the Project Gutenberg™ License for all works posted with the permission of the copyright holder found at the beginning of this work.

1.E.4. Do not unlink or detach or remove the full Project Gutenberg™ License terms from this work, or any files containing a part of this work or any other work associated with Project Gutenberg™.

1.E.5. Do not copy, display, perform, distribute or redistribute this electronic work, or any part of this electronic work, without prominently displaying the sentence set forth in paragraph 1.E.1 with active links or immediate access to the full terms of the Project Gutenberg™ License.

1.E.6. You may convert to and distribute this work in any binary, compressed, marked up, nonproprietary or proprietary form, including any word processing or hypertext form. However, if you provide access to or distribute copies of a Project Gutenberg™ work in a format other than “Plain Vanilla ASCII” or other format used in the official version posted on the official Project Gutenberg™ website (www.gutenberg.org), you must, at no additional cost, fee or expense to the user, provide a copy, a means of exporting a copy, or a means of obtaining a copy upon request, of the work in its original “Plain Vanilla ASCII” or other form. Any alternate format must include the full Project Gutenberg™ License as specified in paragraph 1.E.1.

1.E.7. Do not charge a fee for access to, viewing, displaying, performing, copying or distributing any Project Gutenberg™ works unless you comply with paragraph 1.E.8 or 1.E.9.

1.E.8. You may charge a reasonable fee for copies of or providing access to or distributing Project Gutenberg™ electronic works provided that:

- • You pay a royalty fee of 20% of the gross profits you derive from the use of Project Gutenberg™ works calculated using the method you already use to calculate your applicable taxes. The fee is owed to the owner of the Project Gutenberg™ trademark, but he has agreed to donate royalties under this paragraph to the Project Gutenberg Literary Archive Foundation. Royalty payments must be paid within 60 days following each date on which you prepare (or are legally required to prepare) your periodic tax returns. Royalty payments should be clearly marked as such and sent to the Project Gutenberg Literary Archive Foundation at the address specified in Section 4, “Information about donations to the Project Gutenberg Literary Archive Foundation.”

- • You provide a full refund of any money paid by a user who notifies you in writing (or by e-mail) within 30 days of receipt that s/he does not agree to the terms of the full Project Gutenberg™ License. You must require such a user to return or destroy all copies of the works possessed in a physical medium and discontinue all use of and all access to other copies of Project Gutenberg™ works.

- • You provide, in accordance with paragraph 1.F.3, a full refund of any money paid for a work or a replacement copy, if a defect in the electronic work is discovered and reported to you within 90 days of receipt of the work.

- • You comply with all other terms of this agreement for free distribution of Project Gutenberg™ works.

1.E.9. If you wish to charge a fee or distribute a Project Gutenberg™ electronic work or group of works on different terms than are set forth in this agreement, you must obtain permission in writing from the Project Gutenberg Literary Archive Foundation, the manager of the Project Gutenberg™ trademark. Contact the Foundation as set forth in Section 3 below.

1.F.

1.F.1. Project Gutenberg volunteers and employees expend considerable effort to identify, do copyright research on, transcribe and proofread works not protected by U.S. copyright law in creating the Project Gutenberg™ collection. Despite these efforts, Project Gutenberg™ electronic works, and the medium on which they may be stored, may contain “Defects,” such as, but not limited to, incomplete, inaccurate or corrupt data, transcription errors, a copyright or other intellectual property infringement, a defective or damaged disk or other medium, a computer virus, or computer codes that damage or cannot be read by your equipment.

1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right of Replacement or Refund” described in paragraph 1.F.3, the Project Gutenberg Literary Archive Foundation, the owner of the Project Gutenberg™ trademark, and any other party distributing a Project Gutenberg™ electronic work under this agreement, disclaim all liability to you for damages, costs and expenses, including legal fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH DAMAGE.

1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a defect in this electronic work within 90 days of receiving it, you can receive a refund of the money (if any) you paid for it by sending a written explanation to the person you received the work from. If you received the work on a physical medium, you must return the medium with your written explanation. The person or entity that provided you with the defective work may elect to provide a replacement copy in lieu of a refund. If you received the work electronically, the person or entity providing it to you may choose to give you a second opportunity to receive the work electronically in lieu of a refund. If the second copy is also defective, you may demand a refund in writing without further opportunities to fix the problem.

1.F.4. Except for the limited right of replacement or refund set forth in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.

1.F.5. Some states do not allow disclaimers of certain implied warranties or the exclusion or limitation of certain types of damages. If any disclaimer or limitation set forth in this agreement violates the law of the state applicable to this agreement, the agreement shall be interpreted to make the maximum disclaimer or limitation permitted by the applicable state law. The invalidity or unenforceability of any provision of this agreement shall not void the remaining provisions.

1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the trademark owner, any agent or employee of the Foundation, anyone providing copies of Project Gutenberg™ electronic works in accordance with this agreement, and any volunteers associated with the production, promotion and distribution of Project Gutenberg™ electronic works, harmless from all liability, costs and expenses, including legal fees, that arise directly or indirectly from any of the following which you do or cause to occur: (a) distribution of this or any Project Gutenberg™ work, (b) alteration, modification, or additions or deletions to any Project Gutenberg™ work, and (c) any Defect you cause.

Section 2. Information about the Mission of Project Gutenberg™

Project Gutenberg™ is synonymous with the free distribution of electronic works in formats readable by the widest variety of computers including obsolete, old, middle-aged and new computers. It exists because of the efforts of hundreds of volunteers and donations from people in all walks of life.

Volunteers and financial support to provide volunteers with the assistance they need are critical to reaching Project Gutenberg™’s goals and ensuring that the Project Gutenberg™ collection will remain freely available for generations to come. In 2001, the Project Gutenberg Literary Archive Foundation was created to provide a secure and permanent future for Project Gutenberg™ and future generations. To learn more about the Project Gutenberg Literary Archive Foundation and how your efforts and donations can help, see Sections 3 and 4 and the Foundation information page at www.gutenberg.org.

Section 3. Information about the Project Gutenberg Literary Archive Foundation

The Project Gutenberg Literary Archive Foundation is a non-profit 501(c)(3) educational corporation organized under the laws of the state of Mississippi and granted tax exempt status by the Internal Revenue Service. The Foundation’s EIN or federal tax identification number is 64-6221541. Contributions to the Project Gutenberg Literary Archive Foundation are tax deductible to the full extent permitted by U.S. federal laws and your state’s laws.

The Foundation’s business office is located at 809 North 1500 West, Salt Lake City, UT 84116, (801) 596-1887. Email contact links and up to date contact information can be found at the Foundation’s website and official page at www.gutenberg.org/contact

Section 4. Information about Donations to the Project Gutenberg Literary Archive Foundation

Project Gutenberg™ depends upon and cannot survive without widespread public support and donations to carry out its mission of increasing the number of public domain and licensed works that can be freely distributed in machine-readable form accessible by the widest array of equipment including outdated equipment. Many small donations ($1 to $5,000) are particularly important to maintaining tax exempt status with the IRS.

The Foundation is committed to complying with the laws regulating charities and charitable donations in all 50 states of the United States. Compliance requirements are not uniform and it takes a considerable effort, much paperwork and many fees to meet and keep up with these requirements. We do not solicit donations in locations where we have not received written confirmation of compliance. To SEND DONATIONS or determine the status of compliance for any particular state visit www.gutenberg.org/donate.

While we cannot and do not solicit contributions from states where we have not met the solicitation requirements, we know of no prohibition against accepting unsolicited donations from donors in such states who approach us with offers to donate.

International donations are gratefully accepted, but we cannot make any statements concerning tax treatment of donations received from outside the United States. U.S. laws alone swamp our small staff.

Please check the Project Gutenberg web pages for current donation methods and addresses. Donations are accepted in a number of other ways including checks, online payments and credit card donations. To donate, please visit: www.gutenberg.org/donate.

Section 5. General Information About Project Gutenberg™ electronic works

Professor Michael S. Hart was the originator of the Project Gutenberg™ concept of a library of electronic works that could be freely shared with anyone. For forty years, he produced and distributed Project Gutenberg™ eBooks with only a loose network of volunteer support.

Project Gutenberg™ eBooks are often created from several printed editions, all of which are confirmed as not protected by copyright in the U.S. unless a copyright notice is included. Thus, we do not necessarily keep eBooks in compliance with any particular paper edition.

Most people start at our website which has the main PG search facility: www.gutenberg.org.

This website includes information about Project Gutenberg™, including how to make donations to the Project Gutenberg Literary Archive Foundation, how to help produce our new eBooks, and how to subscribe to our email newsletter to hear about new eBooks.

Table of Contents

- A BOY’S TEXT BOOK ON GAS ENGINES

- PREFACE

- A BOY’S TEXT BOOK ON GAS ENGINES INTRODUCTION

- THE FOUR-STROKE CYCLE.
- THE CYLINDER
- VALVES
- THE PISTON
- THE CRANK SHAFT
- THE CONNECTING ROD
- THE CRANK CASE
- THE CARBURETOR
- THE IGNITION SYSTEM
- THE COOLING SYSTEM
- THE TWO-CYCLE MOTOR.
- INDEX
- Transcriber’s Notes
- THE FULL PROJECT GUTENBERG LICENSE